BOARD
 ID="WDC0101"
 NAME="Western Digital WD1009V-MM1 Winchester Controller"
 MFR="Western Digital"
 CATEGORY="MSD"
 SLOT=ISA16
 LENGTH=320
 READID=YES
 IOCHECK= VALID
 HELP="
 Use the V)iew D)etail by Slot mode to see Configuration
 Options.  Use E)dit Change F)unction to select Options."
;
JUMPER (5) = 15
 NAME="W5"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-15) "1 | 2" "3 | 4" "5 | 6" "7 | 8" "9 |10" "11|12" "13|14" 
  "15|16" "17|18" "19|20" "21|22" "23|24" "25|26" "27|28" "29|30" 
   
 INITVAL=LOC(1-15) 1xxxxxxxxxxxxxx
 FACTORY=LOC(1-15) 100000100000000
 COMMENTS="
[ W5 ]\t 0: Not jumpered, 1: jumpered\n
1 - 2\t1: enable 64k buffer, t0: Reserved\n
3 - 4\t1: enable alternate sector\n
5 - 6\t1: disable translation \n
7 - 8\t1: physical mode, 0: force 35 spt (10mhz only)\n
9 -10\t1: 7byte ECC, 0: 4byte ECC\n
11-12\t1: disable caching.\n
13-14\t1: BIOS PROM 27C128\n
15-16\t1: Reserved\n
17-18\t0: BIOS address at (c800:0), t1: (cc00:0)\n
19-20\t1: BIOS disable\n
21-24  21-22\t 23-24\tIRQ\n
\t0 \t0 \t14\n
\t0 \t1 \t15\n
\t1 \t0 \t12\n
\t1 \t1 \t11\n
25-26\t0: DMA6, 1: DMA7\n
27-28\t0: Primary IO address\n
29-30\t1: Controller disable"

JUMPER (3) = 1
 NAME="W3"
 JTYPE=PAIRED
 VERTICAL=YES
 LABEL=LOC(1)"1-2"
 FACTORY=LOC(1) 0
 COMMENTS="
 W3 1-2 : out for EISA autoconfiguration disable \n
 W3 1-2 : in for EISA autoconfiguration enable "

JUMPER (6) = 1
 NAME="W6"
 JTYPE=PAIRED
 VERTICAL=YES
 REVERSE=YES
 LABEL=LOC(1) "1-2"
 FACTORY=LOC(1) 0
 COMMENTS="
 W6 1-2:  in - card enabled by EISA host.\n
\tout - card enabled all times "
;

IOPORT(2) = 0ZC85H
	SIZE=BYTE
	INITVAL=0XXXXXXX
			;RESERVE BIT 7 (8 BIT BIOS FOR NOW!)
;
IOPORT(3) = 0ZC86H
	SIZE=BYTE
	INITVAL=00XXXXX0
;
IOPORT(1) = 0ZC84H	;WRITE THIS PORT LAST
	SIZE=BYTE
	INITVAL=00000X0X

GROUP="EISA AUTOCONFIGURATION MODE 
(TO USE THIS FEATURE W3 MUST BE INSTALLED!)"

FUNCTION="Fixed Disk Controller Options"
TYPE="MSD,DSKCTL"
HELP="Use E)dit Change F)unction to Select Options."
SUBFUNCTION="IO Address"

;
CHOICE="Primary"
 FREE
  PORT=1F0h-1F7h
;  PORT=3F6h -3F7h
;  SHARE=YES
	INIT=IOPORT(2) LOC(1 0) 00
        INIT=JUMPER(5)LOC(14-15) 00

CHOICE="Secondary"
 FREE
  PORT=170h-177h
  PORT=376h
  PORT=377h
  SHARE=YES
	INIT=IOPORT(2) LOC(1 0) 10
  	INIT=JUMPER(5)LOC(14-15) 10
CHOICE="Disabled"
  FREE
	INIT=IOPORT(2) LOC(1 0) 01
	INIT=JUMPER(5)LOC(14-15) 01
;
SUBFUNCTION="DMA Channel"
CHOICE="DMA 6"
  FREE	
	DMA=6
	INIT=IOPORT(2) LOC(2) 0
  INIT=JUMPER(5)LOC(13) 0

CHOICE="DMA 7"
  FREE	
	DMA=7
	INIT=IOPORT(2) LOC(2) 1
  INIT=JUMPER(5)LOC(13) 1

;
SUBFUNCTION="Interrupt Request Line"
CHOICE="IRQ 14"
  FREE	
	IRQ=14
	INIT=IOPORT(2) LOC(4 3) 00
  INIT=JUMPER(5)LOC(11-12) 00

;
CHOICE="IRQ 15"
  FREE	
	IRQ=15
	INIT=IOPORT(2) LOC(4 3) 01
  INIT=JUMPER(5)LOC(11-12) 01

;
CHOICE="IRQ 12"
  FREE	
	IRQ=12
	INIT=IOPORT(2) LOC(4 3) 10
  INIT=JUMPER(5)LOC(11-12) 10

;
CHOICE="IRQ 11"
  FREE	
	IRQ=11
	INIT=IOPORT(2) LOC(4 3) 11
  INIT=JUMPER(5)LOC(11-12) 11

;
SUBFUNCTION="BIOS Memory Address"
CHOICE="C800:0"
  FREE	
	MEMORY=16K
	ADDRESS=0C8000h
	INIT=IOPORT(2) LOC(6 5) 00	
  	INIT=JUMPER(5)LOC(10-7) 0001 ;FORCE 8 BIT/27128 HERE
;
CHOICE="CC00:0"
  FREE	
	MEMORY=16K
	ADDRESS=0CC000h
	INIT=IOPORT(2) LOC(6 5) 10
   	INIT=JUMPER(5)LOC(10-7) 0101 ;FORCE 8 BIT/27128

;
CHOICE="Disabled"
  FREE	
	INIT=IOPORT(2) LOC(6 5) 01
  	INIT=JUMPER(5)LOC(9-10) 01

;

FUNCTION="Fixed Disk Controller Operational Options"
HELP="Use E)dit Change F)unction to Select Options."

SUBFUNCTION="Caching"
CHOICE="Enabled"
  FREE	
	INIT=IOPORT(3) LOC(1) 0
  INIT=JUMPER(5)LOC(6) 0

CHOICE="Disabled"
  FREE	
	INIT=IOPORT(3) LOC(1) 1
  INIT=JUMPER(5)LOC(6) 1

SUBFUNCTION="ECC Length"
CHOICE="4-byte ECC"
  FREE	
	INIT=IOPORT(3) LOC(2) 0
  INIT=JUMPER(5)LOC(5) 0

;
CHOICE="7-byte ECC"
  FREE	
	INIT=IOPORT(3) LOC(2) 1
  INIT=JUMPER(5)LOC(5) 1

;
SUBFUNCTION="Sector Per Track"
CHOICE="From Drive"
  FREE	
	INIT=IOPORT(3) LOC(3) 0
  INIT=JUMPER(5)LOC(4) 0
;
CHOICE="Force 35 Sector Per Track
(for 10Mhz drives only)"
  FREE	
	INIT=IOPORT(3) LOC(3) 1
  INIT=JUMPER(5)LOC(4) 1

;
SUBFUNCTION="Translation Mode"
CHOICE="Enabled"
  FREE	
	INIT=IOPORT(3) LOC(4) 0
  INIT=JUMPER(5)LOC(3) 0

;
CHOICE="Disabled"
  FREE	
	INIT=IOPORT(3) LOC(4) 1
  INIT=JUMPER(5)LOC(3) 1

;
SUBFUNCTION="Alternate Sector"
CHOICE="Disabled"
  FREE	
	INIT=IOPORT(3) LOC(5) 0
  INIT=JUMPER(5)LOC(2) 0

;
CHOICE="Enabled"
  FREE	
	INIT=IOPORT(3) LOC(5) 1
  INIT=JUMPER(5)LOC(2) 1

;
;
ENDGROUP
;
GROUP="THE FOLLOW OPTION CAN ONLY BE SET BY MANUAL JUMPER SETTINGS"
;
FUNCTION="EISA AUTOCONFIGURATION"
CHOICE="ENABLED"
FREE
INIT=JUMPER(3) LOC(1) 1
CHOICE="DISABLE"
FREE
INIT=JUMPER(3) LOC(1) 0
;
FUNCTION="EISA MODE SELECT"
CHOICE="CARD ENABLED AT ALL TIMES"
FREE
INIT=JUMPER(6) LOC(1) 0
CHOICE="CARD ENABLED BY ESIA HOST"
FREE
INIT=JUMPER(6) LOC(1) 1
;
ENDGROUP

SOFTWARE(1)="
 Installation procedure: \n
 \t Run CF.EXE and set hard drive to type 1. \n
 \t Boot DOS, and run DEBUG. \n
 \t At debug prompt '-', Type G=C800:5 \n
 \t     (or CC00:5 if W5 17-18 is installed)"