         C O M P A Q (R)  C O M P U T E R  C O R P O R A T I O N

                         Compaq Support Paq for
                         Microsoft Windows NT 4.0
                 

1.  INTRODUCTION

This file contains information regarding use of the Compaq Support Paq for
Microsoft Windows NT 4.0.  The following information is provided:

    Support Paq Installation
    Component Usage
    Log File Usage


2.  SUPPORT PAQ INSTALLATION

The primary method for installing the Support Paq is to run the SETUP.EXE
program included with the Support Paq.  By default, all software is selected 
for installation.  In most circumstances, this default selection should not be
altered, and installation is as simple as pressing the "Install" button.  Even
when selected, only software that is appropriate for the system it is being run
on will actually be installed.  Press the "Install" button to proceed with the
installation.  After installation of the appropriate software the utility will
display its results, including indication of software successfully installed,
software not needed for the current system configuration and any installation
failures.  For more information on the usage of SETUP.EXE, refer to the help
file (SETUP.HLP).

A BP000051.CMD file is also provided with the Support Paq for use
in installing the Support Paq from a command prompt without user interaction.
As with the SETUP.EXE program, all software appropriate for the system it is
being run on will be installed.

The Compaq Support Paq for Microsoft Windows NT 4.0 contains numerous files.  All
files must be present in the same directory as the SETUP.EXE program or in 
order for the Support Paq to be installed properly.

A console version of the setup application (SETUPC.EXE) is also provided as a
way to script installations of the Support Paq or components.  For more
information on its usage, refer to the help file (SETUPC.HLP).


3.	COMPONENT USAGE

In addition to the SETUP.EXE program mentioned above, the Support Paq contains
individual .EXE files corresponding to the various components that make up the
Support Paq. If necessary, these components can be installed individually or
their contents extracted to a floppy diskette for use during OS installation.

To install an individual component just run the appropriate CPxxxxx.EXE file 
and chose the "Install" button.

To extract the contents of a component to diskette run the appropriate 
CPxxxxx.EXE file, then chose the "Extract" button instead of the "Install" 
button.

The following table specifies the Compaq software contained within and 
installed by each component.

cp001092.exe	Compaq System Management Driver for Windows NT 4.0
cp001093.exe	Compaq Smart Array 5x Controller Driver For Windows NT 4.0
cp000742.exe	Compaq Smart Array-2 Controllers Driver for Windows NT 4.0
cp001095.exe	Compaq Drive Array Driver for Windows NT 4.0
cp000744.exe	Compaq 32-Bit SCSI Controller Driver for Windows NT 4.0
cp001097.exe	Compaq StorageWorks Fibre Channel Host Bus Adapter for Windows NT 4.0
cp000746.exe	Compaq CMD 0649 IDE Ultra DMA Controller Driver  For Windows NT 4.0
cp001114.exe	Compaq Integrated Ultra ATA-100 Dual Channel Driver For Windows NT 4.0
cp000750.exe	Compaq Remote Insight Board Driver for Windows NT 4.0
cp001100.exe	Compaq Remote Insight Board Wide Area Network Driver for Windows NT 4.0
cp001101.exe	Compaq 64-Bit/66-Mhz Dual Channel Wide Ultra3 SCSI Controller Driver for Windows NT 4.0
cp001099.exe	Compaq ProLiant Storage System Support for Windows NT 4.0
cp000751.exe	Compaq Remote Monitor Service for Windows NT 4.0
cp000752.exe	Compaq Integrated Management Display Utility for Windows NT 4.0
cp000753.exe	Compaq Integrated Management Log Viewer for Windows NT 4.0
cp000754.exe	Compaq Power Supply Viewer for Windows NT 4.0
cp000755.exe	Compaq PCI Hot Plug Utility for Windows NT 4.0
cp000756.exe	Compaq Array Redundancy Software for Windows NT 4.0
cp000757.exe	Compaq Power Down Manager for Windows NT 4.0
cp000758.exe	Compaq Enhanced Integrated Management Display Service for Windows NT 4.0
cp000759.exe	Compaq ATI RAGE IIC Video Controller Driver for Windows NT 4.0
cp000760.exe	Compaq ATI RAGE XL Video Controller Driver for Windows NT 4.0
cp001113.exe	Compaq Array Configuration Utility for Windows NT 4.0
cp001130.exe	Compaq Integrated ATA RAID Management Utility
cp001148.exe	Compaq NetFlex/Netelligent Adapter Driver for Windows NT 4.0
cp001147.exe	Compaq Ethernet/Fast Ethernet or Gigabit NIC Driver for Windows NT 4.0
cp001115.exe	Compaq Foundation Agents for Windows
cp001116.exe	Compaq Server Agents for Windows
cp001118.exe	Compaq Storage Agents for Windows
cp001117.exe	Compaq NIC Agents for Windows
cp001119.exe	Compaq Survey Utility for Windows

4.  LOG FILE USAGE

Progress and results of the installation of all software included in the Support
Paq is logged to the file %SystemDrive%\cpqsystem\log\cpqsetup.log.  This file can be
viewed with any text editor.  Information for subsequent installations is
appended to this log file, providing a chronological history of installation
activity for all software installed by the Support Paq installation utilities.

----------------------------------------------------------------
Copyright 2001, Compaq Computer Corporation. All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
