         C O M P A Q (R)  C O M P U T E R  C O R P O R A T I O N

                         Compaq Support Paq for
                         Microsoft Windows NT 4.0


1.  INTRODUCTION

This file contains information regarding use of the Compaq Support Paq for
Microsoft Windows NT 4.0.  The following information is provided:

    Support Paq Installation
    Component Usage
    Log File Usage


2.  SUPPORT PAQ INSTALLATION

The primary method for installing the Support Paq is to run the SETUP.EXE
program included with the Support Paq.  By default, all software is selected 
for installation.  In most circumstances, this default selection should not be
altered, and installation is as simple as pressing the "Install" button.  Even
when selected, only software that is appropriate for the system it is being run
on will actually be installed.  Press the "Install" button to proceed with the
installation.  After installation of the appropriate software the utility will
display its results, including indication of software successfully installed,
software not needed for the current system configuration and any installation
failures.  For more information on the usage of SETUP.EXE, refer to the help
file (SETUP.HLP).

A BP000068.CMD file is also provided with the Support Paq for use 
in installing the Support Paq from a command prompt without user interaction.
As with the SETUP.EXE program, all software appropriate for the system it is
being run on will be installed.

The Compaq Support Paq for Microsoft Windows NT 4.0 contains numerous files.  All
files must be present in the same directory as the SETUP.EXE program in 
order for the Support Paq to be installed properly.

A console version of the setup application (SETUPC.EXE) is also provided as a
way to script installations of the Support Paq or components.  For more
information on its usage, refer to the help file (SETUPC.HLP).


3.  COMPONENT USAGE

In addition to the SETUP.EXE program mentioned above, the Support Paq contains
individual .EXE files corresponding to the various components that make up the 
Support Paq.  If necessary, these components can be installed individually or 
their contents extracted to a floppy diskette for use during OS installation.

To install an individual component just run the appropriate CPxxxxx.EXE file
and chose the "Install" button.

To extract the contents of a component to diskette run the appropriate
CPxxxxx.EXE file, then chose the "Extract" button instead of the "Install"
button.

3.1 COMPONENT CONFIGURATION

Component files now offer optional support configuration before they are
installed. The optional support configuration allows component-specific 
settings to be written into the .EXE file for availability during installation.

Configuration is performed using the CPCONFIG.EXE program included with the
Support Paq. When the program is executed, it displays a list of all components
in the current directory that support configuration. To configure a component,
click on the component name.

NOTE:   To configure a package, the configuration tool and Support Paq must be
in a write accessible location. A CD or read-only network share is not supported.

To know when a component was last configured, execute the component and view 
the date and time below the component name and version.

The following table specifies the Compaq software contained within and 
installed by each component. Components that have an asterisk (*) next to
their filename support configuration by the CPCONFIG.EXE program described
above:

cp001426.exe    Compaq System Management  Driver for Windows NT 4.0
cp001427.exe    Compaq Smart Array 5x Controller Driver for Windows NT 4.0
cp001428.exe    Compaq Smart Array-2 Controllers Driver for Windows NT 4.0
cp001610.exe    Compaq Drive Array Driver for Windows NT 4.0
cp001601.exe    Compaq 32-Bit SCSI Controller Driver for Windows NT 4.0
cp001429.exe    Compaq StorageWorks Fibre Channel Host Bus Adapter Driver for Windows NT 4.0
cp001602.exe    Compaq CMD 0649 Ultra DMA IDE Controller Driver for Windows NT 4.0
cp001461.exe    Compaq Integrated Ultra ATA-100 Dual Channel Driver for Windows NT 4.0
cp001628.exe    Compaq 64-Bit/66-Mhz Dual Channel Wide Ultra3 SCSI Controller Driver for Windows NT 4.0
cp001385.exe    Compaq Proliant Storage System Support for Windows NT 4.0
cp001603.exe    Compaq Remote Insight Board Driver for Windows NT 4.0
cp001228.exe    Compaq Remote Insight Board Wide Area Network Driver for Windows NT 4.0
cp001456.exe    Compaq Integrated Lights-Out Management Interface Driver for Windows NT 4.0
cp001604.exe    Compaq Remote Monitor Service for Windows NT 4.0
cp001465.exe    Compaq Integrated Management Display Utility for Windows NT 4.0
cp001466.exe    Compaq Integrated Management Log Viewer for Windows NT 4.0
cp001467.exe    Compaq Power Supply Viewer for Windows NT 4.0
cp001605.exe    Compaq PCI Hot Plug Utility for Windows NT 4.0
cp001606.exe    Compaq Array Redundancy Software for Windows NT 4.0
cp001468.exe    Compaq Power Down Manager for Windows NT 4.0
cp001607.exe    Compaq Enhanced Integrated Management Display Service for Windows NT 4.0
cp001608.exe    Compaq ATI RAGE IIC Video Controller Driver for Windows NT 4.0
cp001609.exe    Compaq ATI RAGE XL Video Controller Driver for Windows NT 4.0
cp001449.exe    Compaq Array Configuration Utility for Windows NT 4.0
cp001460.exe    Compaq Integrated ATA RAID Management Utility for Windows
cp001672.exe    Compaq NetFlex/Netelligent Adapter Driver for Windows NT 4.0
cp001450.exe    Compaq Ethernet/Fast Ethernet or Gigabit NIC Driver for Windows NT 4.0
cp001451.exe    Compaq NC67xx/NC77xx Gigabit Ethernet NIC Driver for Windows NT 4.0
cp001418.exe*   Compaq Foundation Agents for Windows
cp001419.exe    Compaq Server Agents for Windows
cp001420.exe    Compaq Storage Agents for Windows
cp001421.exe    Compaq NIC Agents for Windows
cp001392.exe*   Compaq Survey Utility for Windows
cp000736.exe    Compaq Version Control Agent for Windows

4.  LOG FILE USAGE

Progress and results of the installation of all software included in the Support
Paq is logged to the file %SystemDrive%\cpqsystem\log\cpqsetup.log.  This file can be
viewed with any text editor.  Information for subsequent installations is
appended to this log file, providing a chronological history of installation
activity for all software installed by the Support Paq installation utilities.

----------------------------------------------------------------
Copyright 2001, Compaq Computer Corporation. All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
