
mach64, 64OS2154.ZIP
*****************************

1.0     Introduction
2.0     Installation Notes
3.0     mach64 1.54 Fixed list

*****************************

1.0     Introduction

The mach64 device drivers supplied here are for OS/2 2.1X and OS/2 WARP 
3.0.

*****************************

2.0     Installation Notes

DO NOT TASK SWITCH WHILE RUNNING THE INSTALL PROGRAM.

1. Ensure that you have a copy LOAD64.ZIP.  It is available on the ATI 
BBS, ftp site (ftp.atitech.ca), and on our CompuServe forum (GO 
ATITECH).

2. Ensure that you have a copy of PKUNZIP.EXE, v1.10 or later.  PKUNZIP 
is available on most BBS and information services, including the ATI 
BBS and CompuServe.

3. Open a full screen DOS session.

4. Unzip LOAD64.ZIP and 64OS2154.ZIP into the same temporary directory 
on your hard disk, then run the LOAD64.EXE utility.  For example:

MD \ATITEMP
PKUNZIP LOAD64.ZIP \ATITEMP
PKUNZIP 64OS2154.ZIP \ATITEMP
CD \ATITEMP
LOAD64.EXE

5. Follow the screen prompts for installing the OS/2 driver.  

6. Once the driver has been installed, you can delete the contents of 
the temporary directory (DEL \ATITEMP\*.*) and delete the directory 
itself (RD \ATITEMP).  

7. We recommend that you keep a copy of the ZIP files (64OS2154.ZIP and 
LOAD64.ZIP), in case you need to install the driver again.      

8. Run DSPINSTL from within an OS/2 window.

9. When the Display Driver Install panel appears, select Primary 
Display and click OK to bring up a list of choices.  You should see an 
option for ATI mach64.

10. Select 'ATI mach64 (Enhanced 1.54)' from the list and click OK. If 
a error message pops-up, which says "The installed adapter does not 
support the selected display driver.  Do you wish to continue?" ignore 
it and click OK.

11. When the source directory panel appears, select 'Change' and enter:
C:\MACH_OS2 (if you don't use c: as you boot drive replace it with the 
appropriate drive letter) Click 'Set' and then 'Install'. After the 
files are copied, exit the OS/2 window or full screen session. Shut 
down and restart your system.

12. The PM driver will first come up in 640x480, 256 colors mode.  Use 
the following steps to change the screen resolutions or number of 
colors:

   a) Open 'OS/2 System' icon.
   b) Open 'System Setup' icon.
   c) Open 'System' icon.
   b) Select the 'Screen' tab.
   e) Select the desired resolution and number of colors from the list.
   f) Double click on the system menu icon or select close from the 
      system menu to close the window.
   g) Shut down and restart your system.


*****************************

3.0     mach64 1.54 Fixed list


Win OS/2 session
WIN-OS/2 fails to launch when the aperture is disabled
Closing Program Manager closes all applications, SEAMLESS WinOS/2

Paradox
GPF occurs intermittently, when loading PARADOX under a seamless 
WinOS/2 session

AOL 2.0
GPF in FMACX.DRV running AOL 2.0 under a WinOS/2 session.

Solitaire Klondike
Incorrect colours are displayed when playing Solitaire Klondike

MicroStation
MicroStation will not display after task switching

ATI Install issue
Diagnostics fail in Full Screen DOS, M64DIAG.EXE
Error message while launching, INSTALL.EXE
Error message, UNINSTALL

